Track Cleaning

Over the years, I have been asked for advice as to how to keep the tracks clean.



You all are running electric trains of sorts on metal tracks. After a while, the "Black Gunk", as I call it, builds up on the tracks, no matter whether you use AC or DC systems. The model scale also does not come into the picture. Employing plastic wheels on your rolling stock only makes it worse.



If you are still using a 'conventional' system (non digital), this will not be so serious, at first. In conventional mode, the tracks are only conveying track voltage (namely speed) to the loco. Simple.



Once you switch to digital operation, the tracks will suddendly take on an additional function. Now they also have to convey digital signals to the locomotive's decoder. This requires a very good electrical connectivity between track and loco. Lightweight locos are more vulnerable to this phenomenon.



Hence, this 'gunk' needs to be gotten rid of, sooner or later.



Most manufacturers offer a "Track Cleaning Car" of sorts, sometimes in multiple car sets. Any of that will work, and is recommended.



In a pinch, a dry soft piece of cloth or a soft paper towel will do the job. Drenching the cloth/paper in "Denatured Alcohol", available at any pharmacy, will shorten and greatly enhance the process.



Proses (see Reynaulds website) offers a handy device called Track Cleaner (Item #TC-001). Look it up. It works for scales Z up to 00. It's about $12.-



Cleaning cars have pads that get dirty after while. They will fail to do the job when they reach a certain stage of contamination. So do the strips that come with the Proses product. Soaking them in common soap solutions or denatured alcohol will not help. You can order replacement pads or strips. Boo! Not necessary.



There is a product available, generically referred to as a "Non residue contact cleaner". Usually a fairly large spray can.



You can find this in places such as Radio Shack. I get mine from a company called MCM (mcmelectronics.com)



You soak the pads/strips for a while. Bingo! It's Miller Time. Have one!



Even if you do all of the above, you may still run into a situation when your blessed loco all of a sudden stops, like an unruly donkey. At that point, don't blame whoever and whatever comes into your frustrated mind.



There could be a connection problem between the individual track segments. You cannot see it. I have experienced this. (@%#*$)



Proses offers a very handy device to check the existing track voltage anywhere on your lay-out. Available for 2-track DC or 3-track AC. Look it up!



Happy railroading, y'all!!

Comments

  • Addendum to the above. In most drug stores or pharmacies you will have to sign for 'Denatured Alcohol', or they may not sell it to without a certain license. I do not know these details.

    In this case, just get ordinary rubbing alcohol (Isopropyl). It will accomplish the task just as well. It does leave a minor residue which, for our purpose, is of no concern.

    If you run Maerklin AC rail, the surface of the pick-up shoes need to be periodically cleaned, as well. A Q-Tip dipped in the cleaning fluid will do this nicely.

    The track center studs you typically don't have to worry about.

    Some time ago, someone told me he is using the smoke generator fluid to clean his tracks. This is a bad idea. This fluid is somewhat oily. Light weight locomotives trying to pull a good drag load will just sit and spin wheels as if on a sheet of black ice.
  • For more comprehensive information go to http://blog.reynaulds.com and read the blog titled: Keep your tracks clean !
  • RandyRailRandyRail United States
    Hi,
       Back in 2010 when i was building my apartment floor layout.  I would was the sections of c track in the sink with dish soap and scrubby sponge used on the rails and studs of the track. It saved me cleaning the track with other products. Even though C-track is not rated for outside the washing worked to remove a decade of glunk on the track. No turnouts or other electric tracks were washed.

     Years ago with my LGB indoor layout I read that wahl clipper oil was good to use. I tried it on my level layout. I would never recommend   it to any one for the track. I lost all traction. I cleaned the track with alcohol several times till some  traction was restored.  It was a month before train lengths were restored/ It was a double track layout with a passing siding on each loop. Three trans ran around seperated and controlled by signals using the magnets and track sensors. I would go into the layout and start the lgb, And the Ho layout above on a different level. I would play computer games on a 386 cpu in the middle, while the trains raion arpound me. A total of eight trains running without control. 

    Randy Knaub
  • for all mod tec stuff that comes out , why has not set a decoder as such to work in WI FI ? or Bluetooth ? would it be better than sending the signal through the tracks ? or via through the air ?

  • Actually, it is a available right now. I saw something like this in Model Railroader while ago. However, it is bigger than a regular DCC decoder.

    Ulrich

  • for as much they can use micro cams with pin hole views , but yet they can not make a sender receive transmitter ? i guess it is not microflops approved BAHAHAHA

  • For cleaning tracks, I used folded-up heavy-duty paper towels -- onto which glass cleaner (Windex or its generic store brand equivalents) has been sprayed. As you wipe the towel along the tracks, you can clearly see the "tracks" of black grime picked up by the paper towel. Keep folding and refolding the paper towel to use new surfaces on different section of track. You may need to add more glass cleaner. Keep going until the cleaner-soaked paper towel no longer picks up dirt.

    You will need to be careful in the area of switches and other complex track work. Check for remnants of the paper towel left behind.

    The ammonia-based glass cleaners are good at picking up oil and grease-based dirt.

    Of course do this with the track power turned off.

    The same process can also be used for cleaning locomotive wheels.

    -- Ernest

  • Ernest , i was going to say about a glass cleaner cloth , but you did for me , but what about metho on the cloth ? as metho dries very fast , but unsure if it leaves any mineral or residue around , years back i use to use surgical metho on my skin to clean the area i needed to inject insulin , but seems i can not buy it now :( and wow that stuff use to remove all the dirt oil and what ever else was there , it dries very fast as well but one would not want to splash it (soak) but on a cloth might work .

  • I use bore cleaning cotton patches and lacquer thinner. Cleans 'em up nice and shiny.

    I've tried the Roco track cleaning car, but it doesn't work well except for very light cleaning duties. The problem is the pad runs over the same area accumulating dirt in the same spot. After about half way around the layout it's dragging so bad the locomotive (with the rest of the train) can't pull it. If I wanted to go to the trouble of yarding the train and just running the cleaning car it would take longer that to just use the bore patches and LT.

    What really makes the most difference is changing furnace filters on a regular basis. This keeps most particulates out of the air and off of the rails.

  • a air purifier ? i have been using the peco rubber that looks like a ink rubber ! but even though it is rubber , i think wearing could be a thing.

  • I have found the biggest cause of dead track sections is oxidized rail joiners. You can clean the top and sides of rails until they gleam but the rail joiners continue to corrode in any environment or track condition. The solutions to this problem are either solder your rail joiners (which presents more problems when rails expand in warm weather), solder leads to EVERY section of rail, or use temporary track like Kato Unitrack or Peco Roadbead A-Track, where you can change out the old rail joiners for new ones whenever it is needed.

  • BR42BR42 Auburn

    Hello:

    I have soldered almost all my rail joiners. I do not have a problem with track expansion, but then the temperature n my train room only varies between 70 and 80 Fahrenheit. One solution is to solder three rail joiners, and to leave the fourth unsoldered. Just connect the soldered sections to power.

    Ulrich

Sign In or Register to comment.